Having a new garage door improves a house’s aesthetics and security. With every passing day, new technology and gadgets are making their way into the market. The situation is no different when it comes to garage doors. You can easily find a good service provided by professional companies. These services include disassembling the old garage doors and replacing them with new ones. However, some DIY methods can help you save cash that you may have to spend on the cost of installation if you go for a service provider. If you’ve got the required ability and knowledge for this job, then you should install a garage door on your own. Here are some amazing and useful tips that you can follow for a safe installation. So, let’s start.
1- Tools Needed for Garage Door Installation
If you want to save time when installing a garage door on your own, you must have the following tools.
- A Philip’s screwdriver
- Wrench
- Drill Machine
- Sockets
- Pliers
- Ladders
- Glasses for safety
- Ladder
2- Materials Required for Garage Door Installation
Without the materials listed below, you can’t proceed with garage door installation. Therefore, make sure you have them along with the tools.
- Ropes
- Garage door kit
- Lubricant
- Stop and Rubber Basket
- Duct tape
- Operator bracket
- Shims
- Easy Tensioning System
3- Releasing Tension from the Garage Door
The first step is to release tension from the garage door, but great care is needed for that. Garage door springs have an exquisite quantity of weight and tension. If these springs are not handled with proper care, they can cause injuries. Before moving forward, you’ll first need to remove the tension of the torsion spring. Follow the following steps to do it:
- Clamp the shaft of the torsion spring using the pliers and then wedge them in opposition to the headwall above the door.
- Insert a metallic rod in one of the holes of the winding cone. Then after holding the rod tightly, loosen the screws on the cone and keep it in place.
- Then remove the springs one by one. Use two rods now so that one can hold the cone and the other can turn it.
4- Installing the Panels of a Sectional Door
After getting the desired tension, you can now proceed to install the garage door. Here is how you can successfully assemble a garage door.
- Begin to attach the hinges on top of every panel.
- Attach shaft supports to the bottom and top panels.
- Place the bottom panel into the gap, followed by checking its level.
- Properly install all the panels making sure that the bottom of the top panel sits perfectly on the top of the previous panel.
5- Installation of the Tracks
In this step, secure the hinges installed on top of the panels and place the wheeled shafts into the facet hinges. After that, install the axle supports and the tracks. Make sure that the wheels lie properly within the track to ensure proper mechanism. Finally, attach the cable to it.
6- Attachment of the Spring Assembly and Bolting the Tracks
After installing the tracks, assemble everything attached to the springs and connect them to the track. Attach the horizontal and vertical tracks to the door after carefully lining them up and then bolt them together.
7- Installation of the Springs
Bolt the two springs with the head bracket by simply connecting the anchors with the springs and attaching the locking cone.
8- Torsion Rod and Pulley Installation
Slide the holes present at the side header bracket and install the tension rod. After that, connect the pulleys with the end of this rod carefully.
9- Cable Attachment
Attach the cable to the pulley from the bottom and then switch the wheel so that force is taut over the pulley. Then carefully tighten all the elements after sliding the wheel onto the header bracket. Finally, attach a pair of pliers to the rod set on the surface of the bracket. This will prevent the rod from spinning when tightening the garage door springs.
10- Tightening the Springs
With the help of the steel rods, at last, you will need to tighten the garage door springs. Consult the manufacturer’s manual to assist and verify what number of turns are probably needed to secure the springs. Once they accomplish the proper tension, secure every bolt to lock the springs into their place. After that, remove the pliers from the rod.
Getting a new garage door installed yourself will help you save money that you can utilize somewhere else. Many service providers charge a lot for installing a door; therefore, it is better to have some skills to do the job yourself. The steps mentioned above will help you install a garage door efficiently and smoothly. Installing a new door is easy; however, if you are replacing an old garage door, you’ll probably need help in disassembling the old one. If you are not sure that you can handle the whole installation process yourself, then hire a good garage door company on time to avoid damages and unnecessary trouble.